Danh sách thiết bị hãng Elap encoder - Elap Vietnam - ANS Vietnam

Single and multi-turn absolute encoders

Absolute Encoders	Absolute encoders always provide the actual position data at the system power on, despite possible shaft rotations; therefore there is no need to reset to the zero point after a power down. Stout and accurate, Elap single and multi turn absolute encoders are the ideal solution to releave motions on operating machines in all industrial fields. The wide choice of mechanical solutions allow to fulfil any application requirement. The different available output signals andvoltage supply range make it possible to interfaceElap absolute rotary encoders to any counting system or PLC controller. The encoders high resolution values allow to employ them for applications needing a high accuracy degree.
Encoder MEM - BUS Single and multiturn encoders with fieldbus Encoder MEM - BUS 8192 steps/revolution – 13 bit Multiturn: 65536 giri – 16 bit Data memory > 21 years Several configurations available Encoder MEM - BUS	Encoder MEM Single and multiturn encoders Encoder MEM High resolution: 5÷13 bit/revolution x 15 bit revolutions SSI serial output Data memory >21 years Position reset function Binary or Gray code Several configurations available Encoder MEM
Encoder MRE Single turn absolute encoders Encoder MRE 8÷13 bit resolution, binary or Gray code SSI, parallel or analogue output NPN or PNP open collector, push-pull output Different mechanical versions available Encoder MRE	Encoder EMA Single turn magnetic encoders Encoder EMA Several mechanical versions Supply voltage 5Vdc or 10/24Vdc or 5/24Vdc Resolution: 4÷ 13 bit, binary code 5V SSI Serial output Encoder EMA
Encoder MRE Single turn absolute encoders Encoder MRE 8÷13 bit resolution, binary or Gray code SSI, parallel or analogue output NPN or PNP open collector, push-pull output Different mechanical versions available Encoder MRE	Encoder EMA Single turn magnetic encoders Encoder EMA Several mechanical versions Supply voltage 5Vdc or 10/24Vdc or 5/24Vdc Resolution: 4÷ 13 bit, binary code 5V SSI Serial output Encoder EMA
Encoder RM36 36 mm diameter Encoder RM36 Ø 36 mm body, single turn absolute encoder RM36-P: 9 bit parallel output RM36-S: 12 bit SSI serial output RM36-V: voltage analogue output 24Vdc or 5 Vdc supply Encoder RM36	Encoder RM22 22 mm diameter Encoder RM22 Ø 22 mm body, single turn absolute encoder RM22-P: 9 bit parallel output RM22-S: 9 bit SSI serial output RM22-A: sin/cos analogue output RM22-V: voltage analogue output 5 Vdc supply voltage Encoder RM22
Incremental encoders Incremental rotary encoders
Trasduttori Elap	Incremental encoders are rotary transducers used to releave length or thickness measures, angles and speed.Incremental encoders are commonly employed on industrial operating machines, combined to counting, visualizing orcontrol systems, to achieve programmed positionings, preset step shifts or simply to display measures of physical magnitudes. Thanks to the innovative electronic circuitry and the excellent quality of the components, Elap encoders ensure high resolution, great accuracy and repeatability. The wide choice of mechanical and electronic solutionsallows to meet all application requirements.
Encoder E620 63.5x63.5 mm square flange Encoder E620 E620, 63.5 x 63.5 mm square flange, centering mask Ø 31.75 mm E650, 63.5 x 63.5 mm square flange centering mask Ø 50 mm Shaft Ø: 6 - 8 - 9,52 - 10 mm Pulses per revolution: 2 ÷ 36000 Encoder E620	Encoder E520 Ø 58 mm round flange Encoder E520 E520, servo coupling, Ø 58 mm round flange, Ø 50 mm centering mask E540, servo coupling, Ø 58 mm round flange, Ø 36 mm centering mask E510, servo coupling, Ø 58 mm round flange, Ø 31.75 mm centering mask Shaft Ø: 6 - 8 – 9.52 - 10 mm RE530, flange type RE0444, Shaft Ø: 11 mm Pulses per revolution: 2 ÷ 36000 Encoder E520
Encoder SEB/SEB-Z Ø 50 mm Encoder SEB 50 mm Ø round flange Ø 10 mm shaft ABS plastic case IP64 protection degree - optional IP65 Axial or radial cable or connector outlet Output signals: NPN open collector, Push-Pull, Line-driver Pulses per revolution: 2 ÷ 10000 Encoder SEB/SEB-Z	Encoder E40 Ø 40 mm Encoder E40 E40, Ø 40 mm round flange, 6 holes on Ø 30 mm E40A, Ø 40 mm round flange, 4 holes on Ø 25.4 mm E40V, Ø 40 mm round flange, M18x1 screw coupling - Shaft Ø: 6 mm optional 4 mm E40M, Hollow shaft encoder for motor coupling - Shaft Ø: 6 or 8 mm Pulses per revolution: 5 ÷ 10000 Encoder E40
Encoder E320 Ø 38 mm Encoder E320 E320: Ø 38 mm round flange, 4 M3 holes on Ø 30 mm Ø 6 mm shaft Radial cable outlte Output signals: NPN open collector, NPN pull-up collector, push-pull, line driver Pulses per revolution: 2 ÷ 1024 IP53 Protection degree Encoder E320	Encoder E30 Ø 30 mm Encoder E30 E30, Ø 30 mm round flange Ø 4mm shaft Axial or radial cable outlet Push-pull, open collector NPN,line driver output signals 2 ÷ 10000 pulses per revolution IP54 protection degree Encoder E30
Encoder RM36 36 mm diameter Incremental encoder RM36 Ø 36 mm body, single turn absolute encoder RM36-I: incremental encoder Pulses per revolution: 128 - 512 - 1024 - 5 V line driver output signal -5 Vdc supply voltage Encoder RM36	Encoder RM22 22 mm diameter Incremental encoder RM22 Ø 22 mm body RM22-I: incremental, 128 pulses per revolution 5 V line driver output signal 5 Vdc supply voltage Encoder RM22
E400/E410/E430/E470 Hollow shaft Encoder E400 E400 - Joint for motor coupling, Ø 53.5 mm flange, E470 - Joint for motor coupling, Ø 72 mm flange, E410 - Hollow shaft for motor coupling E430 - Hollow shaft for motor coupling Fixing by elastic support Pulses per revolution: 2 ÷ 36000 E400 - E410 - E430 - E470	Encoder REV High ppr and glass disc Encoder REV Aluminium case Glass measuring disc Pulses per revolution: 1000 ÷ 36000 Several mechanical versions available Encoder REV
Encoder EP - REP Programmable encoders Encoder EP521 Number of ppr programmable by the user Pulses per revolution: 8 ÷ 2048 Output signals: push/pull or line driver Several mechanical versions available Encoder EP - REP	Encoder EM - REM Magnetic incremental encoders Encoder EM520 Several mechanical versions available Supply voltage: 5Vdc or 8/24Vdc or 5/24Vdc Output signals: push-pull or line driver Pulses per revolution: 8 ÷ 2048 Encoder EM - REM
Linear transducers Incremental linear transducers
Linear transducers	Incremental linear transducers are usually employed on industrial operating machines. Combined to counting,visualizing and control systems they allow to achieve programmedpositionings, pre-determined step shifts and to display length or thickness measures. Elap linear transducers range includes several sensors type:magnetic transducers, digital transducers, wire sensorsand optical scales. Each position sensor can be supplied with different strokes and resolution values.
Linear transducers series PD - PE Linear transducers PD High reading resolution(up to 0.005 mm) Easy mounting method Hig protection against environmental agents (IP65) Strokes: 60 ÷ 990 mm Linear transducers series PD - PE	TMP + MP200 Magnetic transducer TMP + MP200 magnetic transducer The linear magnetic measuring system TM+MP200 consists of themagnetic transducer TM and themagnetic band MP200. TMP + MP200 Magnetic transducer
Optical scale series KD Optical scale series KD The linear optical readers series KD are accurate and reliable, especially suited for applications in severe industrial environments. Optical scale series KD	Optical scale series KP Optical scale series KP The optical linear scales series KP are accurate and reliable. Thanks to theircompact dimensions they can be applied even onsmall-sized machine tools(millers, lathes, grinders, spark erosion machines...). Optical scale series KP
Wire transducers Linear wire transducers
Linear wire transducers	Stout, easy to install, highly protected againstenvironmental agents: ELAP linear wire transducers series HLS and HPS are the ideal solution for thoseindustrial applications which require high accuracy and measuring length up to 12 metres; typical applications are: X-Y tables, hydraulic and pnematic cylinders, packing machines, and wood-, glass-, marble-, sheet-working machineries. The transducer consists of an encoder or a potentiometeroperated by means of a wire-reel mechanism; the wire is out of stainless steel covered with nylon. The potentiometer HPS provides an analogue signal proportional to the linear displacement of the wire, while theencoder HLS provides a number of pulses proportional to the linear displacement of the wire. The inside spring controls the return of the wire to the starting position. For both types the travel speed is 1000/2000 mm/sec., depending on the stroke, and the protection degree granted by the stout anodysed aluminium case is IP64. The connection is by means of a cable 1 m long. The operators will surely appreciate the mounting method, which is particularly easy.
Wire encoder HLS Wire encoder HLS Strokes ranging from 1000 mm to12 m Resolution: 0.04 ÷ 1 mm Series HLS-S: 1000 mm stroke Series HLS-M: 500 ÷ 5000 mm stroke Series HLS-L: 6000 ÷ 12000 mm stroke Wire encoder HLS	Wire potentiometer HPS Wire potentiometer HPS Strokes ranging from 250 mm to8 m Resistance 5 KOhm ±10% Linearity ±0,02% FS Series HPS-S: 250 ÷ 1000 mm stroke Series HPS-M: 500 ÷ 4000 mm stroke Serie HPS-L: 3000 ÷ 8000 mm stroke Wire potentiometer HPS
Linear potentiometers Linear motion potentiometers
Linear potentiometers	Widely employed on industrial operating machines, linear motion potentiometers are specially designed to measure and control linear displacements in absolute mode. Since they are absolute detecting systems,potentiometers keep the actual position data at power off: therefore they are peculiarly suited to be employed on machines where it is difficult to reset the axis zero point at the system power on, for instance if the material machining lasts for long. ELAP offer in terms of linear motion potentiometers includes a variety of mechanical sizes, strokes, resistive values and mounting fittings to meet any application requirement: there are square or round section potentiometers, small-sized potentiometers, with measuring strokes ranging from 25 to 950 mm.
PLS Series Square section case PLS Series 50 ÷ 950 mm strokes 31 mm square section case 6 mm diameter shaft Axial connector outlet IP65 protection degree PLS Series	PL2S Series 2 ball joints PL2S Series 50 ÷ 500 mm strokes 31 mm square section case 2 fixing ball joints at the ends 6 mm diameter shaft Radial connector outlet IP65 protection degree PL2S Series
PL231 Series 2 ball joints PL231 Series 50 ÷ 750 mm strokes 31 mm square section case 2 fixing ball joints at the ends 8 mm diameter shaft Radial connector outlet IP65 protection degree PL231 Series	PM Series Small size PM Series Compact dimensions 21 mm square section case 25 to 150 mm strokes 5 mm diameter shaft Radial connector outlet IP63 protection degree PM Series
PM2S Series Small size – 2 ball joints PM2S Series Compact dimensions 21 mm square section case 25 to 150 mm strokes 5 mm diameter shaft 2 ball joints at the ends Radial connector outlet IP63 protection degree PM2S Series	PR Series Round section PR Series 26 mm diameter round section case 25 to 150 mm strokes 5 mm diameter shaft Radial connector outlet IP65 protection degree PR Series
PR2S Series Round section – 2 ball joints PR2S Series 26 mm diameter round section case 25 to 150 mm strokes 5 mm diameter shaft Radial connector outlet Two ball joints at the ends IP65 protection degree PR2S Series	PLS-V Series Linear potentiometers with analogue output PLS-V Series Strokes: 50 to 950 mm Supply voltage 18÷30Vdc Output: 0÷10dc max.10 mA proportional to the reached position Accuracy: ±0,25% of the measured value Protection degree: IP65 PLS-V Series
PLC axes controllers PLC single and multi-axes controllers
Nexus, Lynx, Vega, Neos	NEXUS, LYNX, VEGA and NEOS, Elap comprehensive series ofmulti-function controllers were designed to make the programming operations and work cycle control easy. All the different versions - for the control of one, two or four axes - avail on a powerful and flexible PLC and on a thoroughlyconfigurable graphical interface: all the systems can be completely set up to fit perfectly in the multi-faceted application realities. The Modbus RTU and CANopencommunication protocols allow for the controllers connectivity. PLC single and multi-axes controllers
Nexus 2 - 4 Axes Nexus 2 - 4 Axes Nexus controls two to four axes by means of its analogue outputs, and can be successfully applied on any kind of industrial processing machines. Nexus	Lynx 1 - 2 Axes Lynx 1 - 2 Axes LYNX efficientlycontrols one or two digital axes by means of its analogue outputs. Lynx
Vega+ 1 - 2 Axes Vega+ 1 - 2 Axes New graphical design and a powerful man-machine interface are the main features of the new controller VEGA+. The wide TFTcolor display is rear-lighted, 4.2 inch wide, with 432x240 pixel resolution and 65000 colours. Its touch screenfunctions are easily set by means of a dedicated program. Vega+	Vega 1 - 2 Axes Vega 1 - 2 Axes The small-sized, powerful and versatilecontroller VEGA runs the automatic operation of machines and production systems of all industrial sectors. In addition to the usual logical, timing and counting operations, its embedded PLCperforms a series of advanced operations, making it possible to engineer complex applications in a simple and direct way. Vega
Neos 1 Axes Neos 1 Axes Small-sized and compact-shapedNEOSfeatures a single axis controller with great potential. Its embedded PLC allows to configure several functional options, tailoringNEOS for any application in thecounting and positioning field as well as for the development of simple logic circuits. Neos
Counters & visualizers Counters & visualizers
Counters & Visualizers	Combined to digital or analogue transducers ELAP counters and readoutssolve all the problems related to counting and displaying lengths or tickness measures, as well as machined pieces numbers. Their application field is virtually infinite, as they can profitably be employed on any industrial machine performing cutting tasks, preset measure machining, dosing, packing, or coiling. ELAP offer in the counting and positioning field has developed in the years, starting from the earliest electro-mechanical counters to the up-to-datemicroprocessor electronic counters with functions settable by the user. Counters & visualizers
CM78 Multi-functional counter/visualizer CM 78 6 displayed digits Several application programs available 2 presets Settable operational modes CM78	CM78N Multi-functional counter/visualizer CM78N 6 displayed digits Counter or positioner type available 2 presets Settable operational modes CM78N
Series VD4 Digital readouts Series VD4 Display of direct current, direct voltage, potentiometer signal, frequency Analogue or digital signals reading Versions with 2 relay outputs available Display range: four digits, with or without - indication (-9999/9999) Series VD4	Series VD3 Digital readouts Series VD3 Display of direct current, direct voltage, potentiometer signal Display range: three digits with or without - indication (-9999/9999) or three digits and a half (1999) Series VD3
CM6 Microprocessor counter CM6 6 displayed digits 2 presets Settable operational modes CM6
Positioners Single and multi-axis positioners
Single and multi-axis positioners	Elap positioners range includes includes several PLC programmable equipments, which can be easily fit into the variegated application realities you can meet in industrial automation. The single axis controller NEOS and the 1 /2-axis controller VEGA are amongELAP most advanced positioners: different programs are available to run on/off positioning and analogueoutput positioning as well as algorithms for specific functions (eg. Cutting banks, trigonometric functions). Special customer programs can be developed by our technical staff or directly by the user.
Neos Single axis positioner/controller Neos 1 Axes Control over 1 axis Embedded PLC Graphical display Applications programs available Neos	Vega Positioner/controller Vega 1 - 2 Axes Control over 1-2 axes Embedded PLC Graphical display Applications programs available Vega
CM72 - CM73 - CM74 Single axis positioners/counters CM72 - CM73 - CM74 Different hardware versions Several programs available RS232 serial line CM72 - CM73 - CM74	CM76 - CM77 Single axis positioners CM 76 - CM 77 Different hardware versions Several software programs available RS232 Serial line CM76 - CM77
AE91 Synchronization axis Electric axis AE 91 Speed and space synchronisation control Eurocard format RS232 Serial line AE91


huy@ansgroup.asia
0934 039 951

Danh mục sản phẩm

Hỗ trợ trực tuyến

Thăm dò ý kiến

Thống kê website

Stock

Danh sách thiết bị hãng Elap encoder - Elap Vietnam - ANS Vietnam

Single and multi-turn absolute encoders

Encoder MEM - BUS

Single and multiturn encoders with fieldbus

Encoder MEM

Single and multiturn encoders

Encoder MRE

Single turn absolute encoders

Encoder EMA

Single turn magnetic encoders

Encoder MRE

Single turn absolute encoders

Encoder EMA

Single turn magnetic encoders

Encoder RM36

36 mm diameter

Encoder RM22

22 mm diameter

Incremental encoders

Incremental rotary encoders

Encoder E620

63.5x63.5 mm square flange

Encoder E520

Ø 58 mm round flange

Encoder SEB/SEB-Z

Ø 50 mm

Encoder E40

Ø 40 mm

Encoder E320

Ø 38 mm

Encoder E30

Ø 30 mm

Encoder RM36

36 mm diameter

Encoder RM22

22 mm diameter

E400/E410/E430/E470

Hollow shaft

Encoder REV

High ppr and glass disc

Encoder EP - REP

Programmable encoders

Encoder EM - REM

Magnetic incremental encoders

Linear transducers

Incremental linear transducers

Linear transducers series PD - PE

TMP + MP200 Magnetic transducer

Optical scale series KD

Optical scale series KP

Wire transducers

Linear wire transducers

Wire encoder HLS

Wire potentiometer HPS

Linear potentiometers

Linear motion potentiometers

PLS Series

Square section case

PL2S Series

2 ball joints

PL231 Series

2 ball joints

PM Series

Small size

PM2S Series

Small size – 2 ball joints

PR Series

Round section

PR2S Series

Round section – 2 ball joints

PLS-V Series

Linear potentiometers with analogue output

PLC axes controllers

PLC single and multi-axes controllers

Nexus